Released ASQ CQI Updated Questions PDF
CQI Dumps and Practice Test (310 Exam Questions)
NEW QUESTION # 11
What is the volume of a sphere with a radius of 21 inches?
Response:
- A. 5541.76 cubic inches
- B. 873800.68 cubic inches
- C. 143.41 cubic inches
- D. 38792.39 cubic inches
Answer: D
NEW QUESTION # 12
Which of the following is included in a process audit?
Response:
- A. Inspection of product after it is finalized
- B. Evaluating a work flow to the quality system
- C. Evaluating a work flow to documented work instructions
- D. Inspection of product before it is finalized
Answer: C
NEW QUESTION # 13
Solve for x. 40 - x2 = -8
Response:
- A. -5.7
- B. 6.9
- C. 5.7
- D. -6.9
Answer: B
NEW QUESTION # 14
You are measuring a part with an angle callout of 38° +/-2°. Which of the following can be used for this measurement?
Response:
- A. Sine plate and surface gage
- B. V-block and distance indicator
- C. Sine bar, gage blocks, and surface gage
- D. Bevel protractor
Answer: D
NEW QUESTION # 15
How many significant digits are in the number 0.046?
Response:
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 16
Which of the following is the most appropriate definition of a datum?
Response:
- A. A center plane or middle of a feature
- B. The primary surface from which a feature has coincident axis
- C. A theoretically exact point, axis, or plane derived from a feature
- D. A physical characteristic of a feature such as a primary surface
Answer: C
NEW QUESTION # 17
What is the diameter of a circle with an area of 112 square meters?
Response:
- A. 11.94 meters
- B. 35.65 meters
- C. 5.97 meters
- D. 10.58 meters
Answer: A
NEW QUESTION # 18
Which of the following shapes of the indenter tip of a hardness tester for metal is associated with the Rockwell test method?
Response:
- A. Diamond pyramid
- B. Conical diamond
- C. 5mm ball
- D. Pin indenter
Answer: B
NEW QUESTION # 19
If only two sides of a triangle are equal, it is called a(n):
Response:
- A. Right triangle
- B. Isosceles triangle
- C. Equilateral triangle
- D. Vertex triangle
Answer: B
NEW QUESTION # 20
Which of the following displays a summary of statistical data for a distribution?
Response:
- A. Histogram
- B. Scatter Diagram
- C. Stem and Leaf
- D. Box Plot
Answer: D
NEW QUESTION # 21
The assumption that the average of subgroup averages of size n is equal to the average of the population from which the samples came is a basis for the:
Response:
- A. central limit theorem
- B. distribution theorem
- C. control chart theorem
- D. standard deviation theorem
Answer: A
NEW QUESTION # 22
A review of a first piece inspection report for an 8 cavity plastic bottle mold indicates that bottles from six of the eight cavities had a finish diameter of exactly 0.415 inches. The upper specification limit for this dimension is 0.415 inches. The first piece inspection was accepted.
Which of the following types of inspector error best fits this example?
Response:
- A. Distraction
- B. Flinching
- C. Bias
- D. Rounding off
Answer: B
NEW QUESTION # 23
A major defect is best described as one that
Response:
- A. may be likely to cause unsafe conditions
- B. is found in the majority of units in a tested lot
- C. is more than 20% out of tolerance
- D. can cause a product to fail
Answer: D
NEW QUESTION # 24
Which of the following regions of the Weibull curve can be described by a time-dependent failure rate function?
Response:
- A. Early life and constant failure rate
- B. None of the above
- C. Constant failure rate and wear-out
- D. Early life and wear-out
Answer: D
NEW QUESTION # 25
Which of the following is true for gage blocks?
Response:
- A. They are used for calibration for other tools.
- B. They are manufactured to tight tolerances on flatness and surface smoothness only.
- C. All of the above
- D. They are used to set length dimensions for a transfer measurement.
Answer: C
NEW QUESTION # 26
Seriousness classifications for quality characteristics and defects are derived from Response:
- A. specifications and failure evidence
- B. equipment and processes
- C. inspection error
- D. maintenance and machine downtime
Answer: A
NEW QUESTION # 27
The plot of the percent of lots expected to be accepted versus the quality of submitted lots is which of the following?
Response:
- A. Operating characteristics curve
- B. Fraction nonconforming curve
- C. Fraction negative curve
- D. Producer/consumer risk curve
Answer: A
NEW QUESTION # 28
Calculate the standard deviation of the following population set of data: 30, 40, 37, 42, 40, 30 Response:
- A. 5.28
- B. 36.5
- C. 4.82
- D. 27.9
Answer: C
NEW QUESTION # 29
Which of the following sampling plans rejects a lot based on the number of nonconformities of individual units?
Response:
- A. Variable.
- B. Single sampling.
- C. Double sampling.
- D. Stratified.
Answer: B
NEW QUESTION # 30
A lot of raw material is received at a Pharmaceutical company. It is assigned a lot number which is tied to the manufacturer's lot number. This unique lot number will be used to identify the material because:
Response:
- A. This will allow the lot of material to be traced back to the manufacturer's lot regardless of where it is used
- B. There is a place on the receiving form for it
- C. The company doesn't agree with the manufacturer's numbering system
- D. The company wants to know it is now in their inventory
Answer: A
NEW QUESTION # 31
What is the tolerance of the combined outlet, static mixer, and feed sections based on the chain dimensioning tolerance method?
Response:
- A. +/- 0.040 = sqrt ((0.02)2 + (0.003)2 + (0.02)2)
- B. None of the above. This combination requires baseline dimensioning because of the presence of a GD & T frame for a datum.
- C. +/- 0.0004
- D. +/- 0.043
Answer: D
NEW QUESTION # 32
In general terms, a highly capable process is when the spread of the process is:
Response:
- A. The same as the specification limits
- B. Equal to or greater than the control limits
- C. Substantially less than the control limits
- D. Substantially less than the specification limits
Answer: D
NEW QUESTION # 33
What type of testing can determine internal defect and requires a couple material such as water of glycerine?
Response:
- A. Liquid penetrant
- B. Machine vision
- C. X-ray
- D. Ultrasonic
Answer: D
NEW QUESTION # 34
A gage with a set of cartridge or contact gage heads to check several dimensions on a part at the same time is called a(n):
Response:
- A. multidimension gage
- B. differential gage
- C. match gage
- D. venturi gage
Answer: A
NEW QUESTION # 35
Which of the following least serves the purpose of component traceability?
Response:
- A. Reduce exposure to economic risk
- B. Meet regulatory requirements
- C. Reduce exposure to mix-ups
- D. Improve process performance
Answer: D
NEW QUESTION # 36
......
CQI Exam Dumps Pass with Updated 2026 Certified Exam Questions: https://testking.pdf4test.com/CQI-actual-dumps.html
